THE NEW SUPERIOR SIGNALLING

DCC CONTROL SYSTEMS

DCC - SIGNALS - POINT MOTORS - OCCUPANCY MODULES

DISCOUNT PRICES AVAILABLE

ModeltrainsUK at Cravenmodels

Model Railway Accessories – UK and Continental Railways

Tel: 01588 660 580 cravenmodels@btconnect.com

TRAINTRONICS COLOUR LIGHT SIGNALS

READY ASSEMBLED COLOUR LIGHT SIGNALS

EASY TO INSTALL – NO SOLDERING OF WIRES etc – 2 TERMINAL BLOCKS INCLUDED.

Can operate with DCC Accessory Decoder if required

TRAINTRONICS AVAILABLE TO ORDER

Tel 01588 660 580

Please do NOT use a HORNBY CONTROLLER to power these signals.

12v DC ONLY Required. Power supply below.

Fixed Voltage Regulated Mains Adaptor 230v AC to 12V DC 400mA Supply CM-MG81C £12.99 plus P & P

WARNING DELICATE ELECTRICS / ELECTRONICS

Beware of STATIC ELECTRICITY on HANDS & TOOLS

DCC and ELECTRONIC COMPONENT HANDLING.

This Signal Kit contains delicate electrics / electronic components. Please read the installation instructions very carefully – Several times.

If in any doubt please contact your Local Electronics Expert. Ensure that you use the correct power supply.

Incorrect installation will cause instant failure and possible short circuiting.

STATIC ELECTRICITY

Static electricity refers to the build up of electric charge on the surface of objects. The static charges remain on an object until they either bleed off to ground or are quickly neutralized by a discharge.

Although charge exchange can happen whenever any two surfaces come into contact and separate, a static charge will only remain when at least one of the surfaces has a high resistance to electrical flow (an electrical insulator).

The effects of static electricity are familiar to most people because we can see, feel and even hear the spark as the excess charge is neutralized when brought close to a large electrical conductor (for example a path to ground),

or a region with an excess charge of the opposite polarity (positive or negative). The familiar phenomenon of a static 'shock' is caused by the neutralization of charge.

Static electricity can reside in people, clothing or tools etc.

The static electricity must be discharged to EARTH before handling any delicate electronic components or computer components.

Use of Magnetic tools should be avoided at all times.

Warranty and Returns www.cravenmodels.com/TERMS.htm

Built-in Circuit Protection, Fading In-Fading Out adjustment,

Plug & Play Interface Circuit Board, LED’s for low power consumption.

TERMINAL BLOCKS INCLUDED - NO SOLDERING REQUIRED

Easy to install - Just follow enclosed instructions

DCC Compatible

Signal Identification Numbers/Lettering included

PART No	TRAINTRONICS SIGNALS	DESCRIPTION	GAUGE	SRP	OUR PRICE
CM-TT100	Traintronics	100 Single Aspect Yellow c/w Interface Board	OO	TBA	TBA
CM-TT101	Traintronics	101 Single Aspect Flashing White OO TBA	OO	TBA	TBA
CM-TT102	Traintronics	102 2-Aspect Red/Green c/w Fading Interface Board - Ground Mounted	OO	12.99	Our Price 11.95
CM-TT102H	Traintronics	102 HEAD ONLY 2-Aspect Red/Green c/w Fading Interface Board
CM-TT103	Traintronics	103 2-Aspect Yellow/Green c/w Fading Interface Board - Ground Mounted	OO	12.99	Our Price 11.69
CM-TT103H	Traintronics	103 HEAD ONLY 2-Aspect Yellow/Green c/w Fading Interface Board		10.99	Our Price 9.89
CM-TT104	Traintronics	104 3-Aspect Red/Yellow/Green c/w Fading Interface Board - Ground Mounted	OO	14.99	Our Price 13.49
CM-TT104H	Traintronics	104 HEAD ONLY 3-Aspect Red/Yellow/Green c/w Fading Interface Board		12.99	Our Price 11.69
CM-TT105	Traintronics	105 3-Aspect Yellow/Green/Yellow c/w Fading Interface Board - Ground Mounted	OO	14.99	Our Price 13.49
CM-TT105H	Traintronics	105 HEAD ONLY 3-Aspect Yellow/Green/Yellow c/w Fading Interface Board		12.99	Our Price 11.69
CM-TT106	Traintronics	106 3-Aspect SPAD OO TBA	OO	TBA	TBA
CM-TT107	Traintronics	107 4-Aspect Red/Yellow/Green/Yellow c/w Fading Interface Board - Ground Mounted	OO	16.99	Our Price 15.29
CM-TT110	Traintronics	110 2-Aspect Red/Green with feather left c/w Interface Board - Ground Mounted	OO	22.99	Our Price 20.69
CM-TT111	Traintronics	111 2-Aspect Red/Green with feather right c/w Interface Board - Ground Mounted	OO	22.99	Our Price 20.69
CM-TT112	Traintronics	112 3-Aspect Red/Yellow/Green with feather left c/w Interface Board - Ground Mounted	OO	24.99	Our Price 22.49
CM-TT113	Traintronics	113 3-Aspect Red/Yellow/Green with feather right c/w Interface Board - Ground Mounted	OO	24.99	Our Price 22.49
CM-TT114	Traintronics	114 4-Aspect with feather left c/w Interface Board - Ground Mounted	OO	26.99	Our Price 24.29
CM-TT115	Traintronics	115 4-Aspect with feather right c/w Interface Board - Ground Mounted	OO	26.99	Our Price 24.29
		DCC UNITS
CM-TT300	Traintronics	300 DCC& DCC FITTED – SLOW MOTION POINT MOTOR – THIS IS NOT A TOY To view small print please increase your screen size to 200% FULL DETAILS GOTO >>> http://www.cravenmodels.com/TRAINTRONICSPOINTMOTORS.htm		19.95	Our Price 18.95
CM-TT301	Traintronics	DCC DC INTERFACE DECODER FOR TRAINTRONICS SIGNALS – THIS IS NOT A TOY		11.75	Our Price 10.58
CM-TT301	Traintronics	DCC DC INTERFACE DECODER – THIS IS NOT A TOY FOR TRAINTRONICS SIGNALS NEW !! Now you can run your colour light signals from your DCC Controller!. This circuit board replaces the one supplied with Traintronics signals. Once you have switched over the boards, simply connect your DCC feed to the correct terminals and off you go! Runs 2, 3 & 4 aspect signals - including those with feathers. IT IS ASSUMED THAT YOU HAVE A GOOD KNOWLEDGE OF DCC SYSTEMS WARNING DELICATE ELECTRICS / ELECTRONICS Beware of STATIC ELECTRICITY on HANDS & TOOLS This Signal Kit contains delicate electrics / electronic components. Please read the installation instructions very carefully – Several times. If in any doubt please contact your Local Electronics Expert. Ensure that you use the correct power supply. Incorrect installation will cause instant failure and possible short circuiting. Cravenmodels – Modeltrainsuk DCC and ELECTRONIC COMPONENT HANDLING. This Signal Kit contains delicate electrics / electronic components. Please read the installation instructions very carefully – Several times. If in any doubt please contact your Local Electronics Expert. Ensure that you use the correct power supply. Incorrect installation will cause instant failure and possible short circuiting. STATIC ELECTRICITY Static electricity refers to the build up of electric charge on the surface of objects. The static charges remain on an object until they either bleed off to ground or are quickly neutralized by a discharge. Although charge exchange can happen whenever any two surfaces come into contact and separate, a static charge will only remain when at least one of the surfaces has a high resistance to electrical flow (an electrical insulator). The effects of static electricity are familiar to most people because we can see, feel and even hear the spark as the excess charge is neutralized when brought close to a large electrical conductor (for example a path to ground), or a region with an excess charge of the opposite polarity (positive or negative). The familiar phenomenon of a static 'shock' is caused by the neutralization of charge. Static electricity can reside in people, clothing or tools etc. The static electricity must be discharged to EARTH before handling any delicate electronic components or computer components. Use of Magnetic tools should be avoided at all times. PLEASE FOLLOW THE ENCLOSED INSTRUCTIONS VERY VERY CAREFULLY To view small print please increase your screen size to 200%		11.75	Our Price 10.58
CM-TT302	Traintronics	302 DCC& DCC FITTED – BLOCK OCCUPANCY DETECTOR MODULE – THIS IS NOT A TOY		9.95	Our Price 8.95
		TRAINTRONICS SIGNAL STRUCTURES
CM-TT180	Traintronics	Modern Style 4 track Gantry Kit (Signal heads not included) OO		29.99	26.99
		This kit is a Brass thin plate pressing and needs to be soldered together
CM-TT181	Traintronics	Steam Era 4 Track Gantry Kit (Signal heads not included) OO		17.50	15.75
		This kit is a Brass thin plate pressing and needs to be soldered together
CM-TT280	Traintronics	N GAUGE SIGNAL GANTRY TT280 - Modern Style FOUR TRACK SIGNAL GANTRY Similar to TT180 above		25.00	22.50
		TRAINTRONICS SIGNALS

CLICK >> << CLICK

DAPOL PLASTIC KIT – Several can be joined together to cover many tracks

This plastic Gantry comes with three dummy non working colour light signals. Some modelers drill a small hole in the centre of each dummy aspect and fit small LED’s into the holes. Can be quite effective. Or use ECKON Wall Signal Kits. ENES10 or 11 or 12 , or Traintronics Heads – shown above.	Dapol CO 17 OO Scale Signal Gantry
www.cravenmodels.com/ECKON.htm << Click	SRP £4.30

WARNING DELICATE ELECTRICS / ELECTRONICS

Beware of STATIC ELECTRICITY on HANDS & TOOLS

DCC and ELECTRONIC COMPONENT HANDLING.

This Signal Kit contains delicate electrics / electronic components. Please read the installation instructions very carefully – Several times.

If in any doubt please contact your Local Electronics Expert. Ensure that you use the correct power supply.

Incorrect installation will cause instant failure and possible short circuiting.

STATIC ELECTRICITY

Static electricity refers to the build up of electric charge on the surface of objects. The static charges remain on an object until they either bleed off to ground or are quickly neutralized by a discharge.

Although charge exchange can happen whenever any two surfaces come into contact and separate, a static charge will only remain when at least one of the surfaces has a high resistance to electrical flow (an electrical insulator).

The effects of static electricity are familiar to most people because we can see, feel and even hear the spark as the excess charge is neutralized when brought close to a large electrical conductor (for example a path to ground),

or a region with an excess charge of the opposite polarity (positive or negative). The familiar phenomenon of a static 'shock' is caused by the neutralization of charge.

Static electricity can reside in people, clothing or tools etc.

The static electricity must be discharged to EARTH before handling any delicate electronic components or computer components.

Use of Magnetic tools should be avoided at all times.

Cravenmodels – Modeltrainsuk

Warranty and Returns www.cravenmodels.com/TERMS.htm

SIGNAL NUMBERS INCLUDED

NOTE - THE ENCLOSED DIAGRAMS ARE FOR GUIDANCE –

YOU MUST FOLLOW THE MANUFACTURERS INSTRUCTIONS.

N GAUGE RANGE OF SIGNALS COMING SOON – WATCH THIS SPACE

WARNING DELICATE ELECTRICS / ELECTRONICS

Beware of STATIC ELECTRICITY on HANDS & TOOLS

DCC and ELECTRONIC COMPONENT HANDLING.

This Signal Kit contains delicate electrics / electronic components. Please read the installation instructions very carefully – Several times.

If in any doubt please contact your Local Electronics Expert. Ensure that you use the correct power supply.

Incorrect installation will cause instant failure and possible short circuiting.

STATIC ELECTRICITY

Static electricity refers to the build up of electric charge on the surface of objects. The static charges remain on an object until they either bleed off to ground or are quickly neutralized by a discharge.

Although charge exchange can happen whenever any two surfaces come into contact and separate, a static charge will only remain when at least one of the surfaces has a high resistance to electrical flow (an electrical insulator).

The effects of static electricity are familiar to most people because we can see, feel and even hear the spark as the excess charge is neutralized when brought close to a large electrical conductor (for example a path to ground),

or a region with an excess charge of the opposite polarity (positive or negative). The familiar phenomenon of a static 'shock' is caused by the neutralization of charge.

Static electricity can reside in people, clothing or tools etc.

The static electricity must be discharged to EARTH before handling any delicate electronic components or computer components.

Use of Magnetic tools should be avoided at all times.

Cravenmodels – Modeltrainsuk

Warranty and Returns www.cravenmodels.com/TERMS.htm

www.cravenmodels.com/SIGNALSHELP.htm << Click

OTHER COMPLEMENTARY PRODUCTS - VIESSMANN

	Viessmann  -  VN4515 HO Scale Marker Signal Banner REPEATER height 55mm - movable banner arm and lit, compact, under baseboard drive unit
	£35.00 OUR PRICE £31.49
	Viessmann  -  VN4516 HO Scale Marker Signal Ground Banner - REPEATER height 15mm - movable banner arm and lit, compact, under baseboard drive unit
	£32.50 OUR PRICE £29.25
	Viessmann  -  VN4517 HO Scale Marker Signal Banner REPEATER - movable banner arm and lit, compact, under baseboard drive unit height 65mm
	Only £34.50 OUR PRICE £30.99

Viessmann  -  VN4617

HO Scale

Marker Signal Banner – REPEATER SIGNAL – Mount within Platform section or Lineside

- height 65mm - movable banner arm and lit, compact, above baseboard drive unit.

£35.50 Our Price £31.90

NOW BACK IN STOCK

ECKON BERKO SIGNAL SWITCHES – CLICK HERE

MODEL RAILWAY WIRE
	Gaugemaster Model Railway Wires All Scales Z to O 4 coils Wire each 7 x 0.2mm by approx 10 Metres long. You select your colours by email sales@cravenmodels.com SELECT FROM RED – WHITE – GREEN – GREY – BROWN – BLACK – BLUE – YELLOW – PINK - ORANGE
	SPR £7.00 Our Price £6.35
	Gaugemaster Model Railway Wires All Scales Z to O 6 coils Wire each 7 x 0.2mm by approx 10 Metres long. You select your colours by email sales@cravenmodels.com SELECT FROM RED – WHITE – GREEN – GREY – BROWN – BLACK – BLUE – YELLOW – PINK - ORANGE
	SPR £10.50 Our Price £9.45
	Gaugemaster Model Railway Wires All Scales Z to O 8 coils Wire each 7 x 0.2mm by approx 10 Metres long. You select your colours by email sales@cravenmodels.com SELECT FROM RED – WHITE – GREEN – GREY – BROWN – BLACK – BLUE – YELLOW – PINK - ORANGE
	SPR £14.00 Our Price £12.60
	Gaugemaster Model Railway Wires All Scales Z to O 10 coils Wire each 7 x 0.2mm by approx 10 Metres long. COLOURS AS SHOWN Order by email sales@cravenmodels.com SELECT FROM RED – WHITE – GREEN – GREY – BROWN – BLACK – BLUE – YELLOW – PINK - ORANGE
	SPR £17.50 Our Price £15.75

SWITCHES

Gaugemaster Point Motor Switch GM510 A5H

All Scales

A5H Mini-Toggle for Point Motors

1 off GM510-1 SPR £2.15 Our Price £1.95

2 0ff GM510-2 SPR £4.30 Our Price £3.87

3 off GM510-3 SPR £6.45 Our Price £5.80

4 off GM510-4 SPR £8.60 Our Price £7.75

	Gaugemaster 2 Aspect SIGNAL SWITCH GM508 A5C All Scales A5C Mini-Toggle for “ Aspect Red/Green Signal On /On
	1 off GM508-1 SPR £1.90 Our Price £1.75 2 0ff GM508-2 SPR £4.30 Our Price £3.45 3 off GM508-3 SPR £6.45 Our Price £5.15 4 off GM508-4 SPR £8.60 Our Price £6.85

Gaugemaster Rotary Switch GM519

All Scales Z to O

A7 Rotary Switch 1 Pole 12 Way

SRP £2.75 Our Price £2.50

	Gaugemaster GM520 All Scales A8 Rotary Switch 2 Pole 6 Way
	SRP £2.75 Our Price £2.50
	Gaugemaster GM521 All Scales A9 Rotary Switch 3 Pole 4 Way
	SRP £2.75 Our Price £2.50
	Gaugemaster GM522 All Scales A10 Rotary Switch 4 Pole 3 Way
	SRP £2.75 Our Price £2.50

Rotary Switches, needless to say, have a rotary switching movement. They will be needed when the number of circuits that need to be changed

simultaneously exceeds the capacity of a toggle or slide switch.

A7, A8, A9 & A10 ROTARY SWITCHES – Will cover multiple switching roles where more than two circuits need to be simultaneously switched - for example if three or four track controllers are being used for ‘cab control’.

This switch can be used to unlatch relays by momentarily interrupting the power supply

to the actuating coil.

£11.69

PCU-1 (Plus PCU 2) 2 ASPECT SIGNAL and PM-1 OR PM-4 POINT MOTOR SUGGESTED WIRING DIAGRAM

www.cravenmodels.com/SEEP.htm <<< Click for Point Motors and switching

www.cravenmodels.com/BERKO.htm <<< Click for Signals and wiring

Fixed Voltage Regulated Mains Adaptor

230v AC to 12V DC 400mA Supply

CM-MG81C

£12.99 plus P & P

Product Features
· Interchangeable output plugs
· Fixed output voltage 12v DC
· Robust black ABS housing
· Thermal fuse protection

Specifications:
Input voltage:	AC 230 V/50Hz
Output current:	12v DC, 400mA max.
Output plugs:	A choice of 6 connectors are provided with the unit: 2.1 x 5mm, 2.5 x 5.5mm, 1.35 x 3.5mm and 1.5 x 5.5mm hollow plugs and 2.5 and 3.5mm mono jacks
Dimensions:	92 x 56 x 76mm
Order	Input	Output	Output
Code:	power:	voltage:	power:
CMMG81C	13.6W	DC 12 V	4.8VA

Green, Yellow, Brown, Orange

Wire 7 x 0.2mm 10 Metres each

Blue, Red, White, Black

	£6.25 for 4 coils
Wire 7 x 0.2mm 10 Metres each

3 Thin wires

	Three coils £ 3.99
5m Super Thin Wire Black / Yellow / Brown 5m each

Switches

SEEP POINTMOTORS

Universal point motors to operate most makes of points

All are water resistant and require between 12 and 25 volts AC or DC at a maximum of 1.5amps to operate. Suggest the use of a CDU

Seep PM-1 Point motor with switch

Scale / Type:	O/ OO/ HO/ N Scales
Part Number:	PM-1
Description:	Seep Point Motors have the advantage of being the only point motors available with variable thrust. They also have the advantage of being easy to fix under the baseboard. requiring only a small slot to operate the point. The PM-1 is our best selling point motor and has a built in changeover switch to operate accessories or change frog polarity.

You need TWO SEPARATE POWER SUPPLIES

One for the POINT MOTOR between 12 and 25 volts AC or DC at a maximum of 1.5 amps to operate the Point Motor.

The Second for THE SIGNAL (ECKON / BERKO or TRAINTRONICS) of 12 DV to operate the Signal.

Seep PM-2 Point motor without switch

Scale / Type:	O/ OO/ HO/ N Scales
Part Number:	PM-2
Description:	Seep Point Motors have the advantage of being the only point motors available with variable thrust. They also have the advantage of being easy to fix under the baseboard. requiring only a small slot to operate the point. The PM-2 is our standard point motor with no changeover switch.

Point Motor shown upside down in packaging

Seep PM-4 Point motor latch (SPRING) & switch

Scale / Type:	O/ OO/ HO/ N Scales
Part Number:	PM-4
Description:	Seep Point Motors have the advantage of being the only point motors available with variable thrust. They also have the advantage of being easy to fix under the baseboard. requiring only a small slot to operate the point. The PM-4 is a self-latching point motor, ideal for use with hand-made points, and also includes a changeover switch for operating accessories or changing frog polarity.

Point Motor shown upside down in packaging

You need TWO SEPARATE POWER SUPPLIES

One for the POINT MOTOR between 12 and 25 volts AC or DC at a maximum of 1.5 amps to operate the Point Motor.

The Second for THE SIGNAL (ECKON / BERKO or TRAINTRONICS) of 12 DV to operate the Signal.

WARNING DELICATE ELECTRICS / ELECTRONICS

Beware of STATIC ELECTRICITY on HANDS & TOOLS

DCC and ELECTRONIC COMPONENT HANDLING.

This Signal Kit contains delicate electrics / electronic components. Please read the installation instructions very carefully – Several times.

If in any doubt please contact your Local Electronics Expert. Ensure that you use the correct power supply.

Incorrect installation will cause instant failure and possible short circuiting.

STATIC ELECTRICITY

Static electricity refers to the build up of electric charge on the surface of objects. The static charges remain on an object until they either bleed off to ground or are quickly neutralized by a discharge.

Although charge exchange can happen whenever any two surfaces come into contact and separate, a static charge will only remain when at least one of the surfaces has a high resistance to electrical flow (an electrical insulator).

The effects of static electricity are familiar to most people because we can see, feel and even hear the spark as the excess charge is neutralized when brought close to a large electrical conductor (for example a path to ground),

or a region with an excess charge of the opposite polarity (positive or negative). The familiar phenomenon of a static 'shock' is caused by the neutralization of charge.

Static electricity can reside in people, clothing or tools etc.

The static electricity must be discharged to EARTH before handling any delicate electronic components or computer components.

Use of Magnetic tools should be avoided at all times.

Cravenmodels – Modeltrainsuk

Warranty and Returns www.cravenmodels.com/TERMS.htm

CRAVENMODELS – MODELTRAINSUK

MODEL RAILWAY AND TRAIN ELECTRICAL & ELECTRONIC KIT COMPONENTS & PRODUCTS

Beware of STATIC ELECTRICITY on HANDS & TOOLS

YOU WILL BE SUPPLIED WITH A KIT CONTAINING ELECTRICAL & ELECTRONIC COMPONENTS WHICH NEED TO BE ASSEMBLED CORRECTLY IN ACCORDANCE WITH THE INSTRUCTIONS PROVIDED

IF YOU ARE USING A POWER SUPPLY PLEASE ALSO READ THESE INSTRUCTIONS.

These products are not toys and Children need to be supervised by an adult at all times.

THE CORRECT POWER SUPPLY MUST BE USED AT ALL TIMES.

There are many different power supplies available within the Model Industry.

It is your responsibility to ensure that you use the correct supply and ensure that the correct polarity is used.

Please read all the manufacturers instructions before attempting to connect any power supply to an electrical device.

If you do not have the necessary knowledge, skills or experience you should employ a Local Qualified Electronics engineer.

Using an INCORRECT power supply and or INCORRECT POLARITY will damage the product.

It may or may not work initially but may burn out due to incorrect voltage or amperage or polarity being used.

There are supplies that are DC or AC. The correct one must be used.

Some products call for the use of Diodes and or Resistors and or Regulators or Decoders and or Controllers. Please use the correct ones.

For further information please email or telephone 01588 660580 or goto www.cravenmodels.com

WARNING DELICATE ELECTRICS / ELECTRONICS

This Signal Kit contains delicate electrics / electronic components.

Please read the installation instructions very carefully – Several times.

If in any doubt please contact your Local Electronics Expert. Ensure that you use the correct power supply.

Incorrect installation will cause instant failure and possible short circuiting invalidating any warranty.

Cravenmodels – Modeltrainsuk

Facilities & Services - Please click on box required

Home

SIGNALS Index

Main Index

About Us

Contact

How to Order

Order Form

Privacy

Returns

Terms

Cravenmodels International Mail Order Company

Craven Model Centre, Bungalow Railway Workshops, Purslow Estate, Craven Arms, Shropshire SY7 0HJ

Tel: 01588 660 580 cravenmodels@btconnect.com

INTERNET TRADING FOR OVER 12 YEARS

CLICK >> << CLICK