Eckon and Berko Model Railway Colour Light Signal Kits available 2013 from Modeltrainsuk at Cravenmodels the UK Model Railway Signal supplier. Plus Train-Tech, Traintronics, Dapol, Berko, Berko N, DC and DCC

ECKON KIT - BERKO ASSEMBLED SIGNALS TRAIN-TECH TRAINTRONICS DC AND DCC 2013 COLOUR LIGHT SIGNALS

FULL CATALOGUE - CRAVEN MODEL RAIL CENTRE MODELTRAINSUK CRAVENMODELS MODEL

RAILWAY SIGNAL COMPANY - TRAINTRONICS SIGNALS - THE CRAVEN MODEL CENTRE - MODEL

RAILWAY KITS - MODEL SUPPLIES. MODEL TRAINS UK CRAVEN MODELS

Modeltrainsuk

at Cravenmodels of Shropshire plus

The Model Railway Signal Company

ECKON KIT SIGNALS CATALOGUE 2013 

email mailto:eckon@btconnect.com

2013 - NEW STOCK ARRIVING

ECKON COLOUR LIGHT SIGNAL KITS

FULL CATALOGUE BELOW

NEW 2013 PRICE LIST BELOW 

COLOUR LIGHT SIGNAL KITS

For BERKO READY ASSEMBLED SIGNALS <<<< Click here

ECKON and BERKO SIGNALS ARE MANUFACTURED BY THE SAME COMPANY

email cravenmodels@btconnect.com or

Telephone 01588 660 580

FULL COLOUR LIGHT SIGNAL INDEX << Click

↓ FULL ECKON “OO” SIGNAL KIT CATALOGUE & WIRING SHOWN BELOW ↓

Please do NOT use a HORNBY TYPE CONTROLLER to power these signals.

12v DC ONLY Required. Power supply shown below.

Please do NOT use a HORNBY TYPE CONTROLLER to power these signals.

12v DC ONLY Required. Power supply shown below.

<< Click to buy

Gaugemaster WM1 Wall Mounted Transformer - 1x 16v AC or 12v DC @ 1.1A

Welcome to Modeltrainsuk at

Cravenmodels of Shropshire

Gaugemaster WM1  Wall Mounted Transformer - 1x 16v AC or 12v DC @ 1.1A  MODELTRAINSUK

PLEASE ENSURE THAT YOU ARE USING THE CORRECT OUTPUT  AC or DC  !!!!!!!!!!!!!!!!!

Gaugemaster M1DC  Cased Transformer 12v DC - Output 2 x 12v DC @ 1A

WARNING DELICATE ELECTRICS / ELECTRONIC COMPONENTS KITS WHICH NEED TO BE ASSEMBLED CORRECTLY

These Signal Kits contain delicate electrics / electronic components.

Please read the installation instructions very carefully – Several times.

If in any doubt please contact your Local Electronics Expert. Ensure that you use the correct power supply.

Incorrect installation will cause instant failure and possible short circuiting invalidating any warranty.

These products are not toys and Children need to be supervised by an adult at all times.

Cravenmodels – Modeltrainsuk

WARNING DELICATE ELECTRICS / ELECTRONIC COMPONENTS KITS WHICH NEED TO BE ASSEMBLED CORRECTLY

These Signal Kits contain delicate electrics / electronic components.

Please read the installation instructions very carefully – Several times.

If in any doubt please contact your Local Electronics Expert. Ensure that you use the correct power supply.

Incorrect installation will cause instant failure and possible short circuiting invalidating any warranty.

These products are not toys and Children need to be supervised by an adult at all times.

Cravenmodels – Modeltrainsuk

2013

Colour Light Signals by Berko & ECKON
Part No.	Product Description BERKO READY ASSEMBLED	Price inc VAT
B223	2 light signal yellow/green standard offset square head	13.99
B228	2 light signal red/green standard square head	13.50
B232	2 light signal red/yellow standard square head	13.50
B242	2 light signal red/green standard offset square head	13.99
B251	2 light signal yellow/green standard square head	13.50
B301	2 light signal red/green platform starter square head	13.50
B30L	2 light signal red/green offset platform starter LH square head	13.99
B30R	2 light signal red/green offset platform starter RH square head	13.99
B362	2 light signal red/green short post T junction square head	17.99
B401	2 light signal yellow/green T junction square head	17.99
B462	2 light signal red/green T junction square head	17.99
B503	3 light signal red/green/yellow standard square head	15.00
B533	3 light signal red/green/yellow T junction square head	18.50
B551	3 light signal red/green/yellow standard offset square head	15.00
B604	4 light signal red/green/2yellow standard square head	15.00
B644	4 light signal red/green/2yellow T junction square head	19.80
B664	4 light signal red/green/2yellow standard offset square head	16.99
B801	3 light signal red/green/yellow ground	12.00
	ECKON KITS
EA1	4mm Etched Brass ladder X3	3.00
EA2	2mm Etched Brass ladder X6	3.60
EA3	Route indicator kit LH	7.75
EA4	Route indicator kit RH	7.75
EA7	Speed Restriction sign kit	6.00
EE1	Lectralok lever switch on/off	6.90
EE2	Lectralok lever switch 2-way	7.50
EE3	Lectralok lever switch 3-way	7.50
EET	8BA N/Silver tags for Lectralok switches (20)	2.40
ES1	2 aspect platform starter kit round head	7.75
ES17	4-2 aspect junction kit round head	13.75
ES18	3-3 aspect home junction kit round head	13.75
ES19	2-2-2 aspect home 3 way junction kit round head	14.40
ES24	position light ground signal kit 2white 1red	10.80
ES24Y	position light ground yard signal kit 2white 1yellow	10.80
ES2D	2 aspect distant kit round head	7.75
ES2H	2 aspect home kit round head	7.75
ES3	3 aspect home kit round head	9.18
ES3D	3 aspect distant kit round head	9.18
ES4	4 aspect section kit round head	10.20
ES5	2-2 aspect home junction kit round head	10.80
ES5D	2-2 aspect distant junction kit round head	10.80
ES6	3-2 aspect home junction kit round head	12.55
ES7L	2 aspect home with RT indicator kit LH round head	15.00
ES7R	2 aspect home with RT indicator kit RH round head	15.00
ES8L	3 aspect home with RT indicator kit LH round head	16.20
ES8R	3 aspect home with RT indicator kit RH round head	16.20
ES9L	4 aspect section with RT indicator LH round head	18.00
ES9R	4 aspect section with RT indicator RH round head	18.00
MODELTRAINSUK at CRAVENMODELS OF SHROPSHIRE

N GAUGE ASSEMBLED COLOUR LIGHT SIGNALS

ENBN02	Berko	2 Aspect (Red/Green) Platform Starter	14.70
ENBN03L	Berko	3 Aspect Offset Platform Starter LH	16.35
ENBN03R	Berko	3 Aspect Offset Platform Starter	16.35
ENBN04T	Berko	N 2 Light (Red/Green) Two Head Island Platform Starter	24.95
ENBN0L	Berko	2 Light Red/Green LH Offset Platform Starter	14.90
ENBN0R	Berko	2 Light Red/Green RH Offset Platform Starter	14.90
ENBN28	Berko	2 Aspect (Red/Green) Signal	14.70
ENBN31	Berko	N 3 Aspect Standard Offset Signal	16.00
ENBN32	Berko	3 Aspect Platform Starter	15.90
ENBN36T	Berko	N 3 Aspect Platform Starter	26.40
ENBN38	Berko	Gauge 3 Aspect (Red/Yellow/Green) Colour Light Signal	15.90
ENBN41	Berko	Offset RH Short Arm (Red/Green) Signal	15.90
ENBN62J	Berko	N Twin Head Two Aspect Junction Signal	29.95
ENBN77	Berko	2 Light Red/Green Ground Signal	11.80

Eckon/Berko  -  ENEA1

OO Scale

Ladder Strip

Eckon/Berko  -  ENEA10

OO Scale

Offset 2 'T 'Junction Arm

SORRY - NO LONGER MANUFACTURED

Eckon/Berko  -  ENEA11

OO Scale

Overtrack Smoke Hoods

Eckon/Berko  -  ENEA12

OO Scale

Handwheels 6mm 6 Spoke

SORRY NO LONGER MANUFACTURED

Eckon/Berko  -  ENEA15STD   Standard Length Post

OO Scale

Signal Ladder, Base & Post Kit (NO SIGNAL HEAD INCLUDED)

Ideal spare for converting or repairing old signals.

Eckon/Berko  -  ENEA15PLAT  Platform mounted Short Length Post (As above but with Short Signal Post)

OO Scale

Signal Ladder, Base & Post Kit - Kit (NO SIGNAL HEAD INCLUDED)

Ideal spare for converting or repairing old signals.

HIGH DEGREE OF SKILL NEEDED >>

Eckon/Berko  -  ENEA3

OO Scale

L/H Route Indicating Head kit 12v DC

To fit this kit to an eckon signal kit, just glue the curved base onto the top rear of the signal head and pass the wires down the signal post as normal.

Then follow the wiring instructions provided with the kit.

A maximum of only 2 FEATHERS can be fitted in a Y configeration, onto one signal due to the size of the curved base of the kits.

To fit 2 feathers, you put a left on the right and the right on the left - You will have to remove one small part of each curved leg very carefully. Skill is needed.

HIGH DEGREE OF SKILL NEEDED >>

Eckon/Berko  -  ENEA4

OO Scale

R/H Route Indicating Head kit 12v DC

To fit this kit to an eckon signal kit, just glue the curved base onto the top rear of the signal head and pass the wires down the signal post as normal.

Then follow the wiring instructions provided with the kit.

A maximum of only 2 FEATHERS can be fitted in a Y configeration, onto one signal due to the size of the curved base of the kits.

To fit 2 feathers, you put a left on the right and the right on the left - You will have to remove one small part of each curved leg very carefully. Skill is needed.

Eckon/Berko  -  ENEA5

OO Scale

Lineside Fog Signalling Apparatus & Hut

Eckon/Berko  -  ENEA6

OO Scale

Fogmans Huts (3)

Eckon/Berko  -  ENEA7

OO Scale

Speed Restriction Sign Fret – Speed restriction signs mounted on short poles at the side of the track.

Eckon/Berko  -  ENEE1

All Scales

On/Off Switch (Green)

Eckon/Berko  -  ENEE2

All Scales

2 Way Centre Off Switch

Eckon/Berko  -  ENEE3

All Scales

3 Way Lever Switch

Eckon/Berko  -  ENEE4
OO/ N Scales	New 2008
Lectralock Lever Switch Passing Contact

Eckon/Berko  -  ENEET
OO/ N Scales	New 2008
8ba Nickel Silver Solder Tags to attach wires to Lever Switches
Now released

Eckon Colour Light Signal Kits and Yard Lighting Kits

Eckon/Berko  -  ENEL1

OO Scale

Electric Yard Lamp Kit

12 to 15v AC/DC Approx height 3.5 inches when assembled

http://www.modeltrainsuk.co.uk/model-railway-lighting-82-c.asp << look new

Eckon/Berko  -  ENEL10

OO Scale

Lighting Lamps & Shades (3)

AVAITING NEW MANUFACTURE

http://www.modeltrainsuk.co.uk/model-railway-lighting-82-c.asp << look new

Eckon/Berko  -  ENEL2

OO Scale

Floodlight Yard Lamp Kit

12 to 15v AC/DC Approx height 4 inches when assembled

AVAITING NEW MANUFACTURE

http://www.modeltrainsuk.co.uk/model-railway-lighting-82-c.asp << look new

Eckon/Berko  -  ENEL3

OO Scale

Gas Type Yard Lamp Kit

12 to 15v AC/DC Approx height 3 inches when assembled

AVAITING NEW MANUFACTURE

http://www.modeltrainsuk.co.uk/model-railway-lighting-82-c.asp << look new

AVAITING NEW MANUFACTURE

http://www.modeltrainsuk.co.uk/model-railway-lighting-82-c.asp << look new JUST CLICK

Eckon/Berko  -  ENEL8

OO Scale

Tall Electric Yard Lamp Double Kit

AVAITING NEW MANUFACTURE

http://www.modeltrainsuk.co.uk/model-railway-lighting-82-c.asp << look new

Eckon/Berko  -  ENELN2

N Scale

Yard Lamp Kit (x 2)

AVAITING NEW MANUFACTURE

ECKON SIGNAL KITS & DCC CONTROL

http://www.modeltrainsuk.co.uk/train-tech-train-tech-sc1-oo-scale-dual-2-aspect-signal-controller-modeltrainsuk-2286-p.asp << CLICK

ECKON SIGNAL KITS

Eckon/Berko  -  ENES1

OO Scale

Kit Two Aspect Platform Mounted Starter Kit 12v DC

Eckon/Berko  -  ENES10

OO Scale

Kit Two Aspect Home Wall Kit

Where there is insufficient room at the side of the track for a post mounted signal a wall mounted one might be used.

These can also be mounted on Dapol Signal Gantries. Please see separate diagram below.

SORRY NO LONGER MANUFACTURED - we have a few in stock

Eckon/Berko  -  ENES10D

OO Scale

Kit One Aspect Distant Wall Kit 12v DC

SORRY NO LONGER MANUFACTURED

Eckon/Berko  -  ENES11

OO Scale

Kit Home Distant Signal 3 Aspect Kit 12v DC

SORRY NO LONGER MANUFACTURED

Eckon/Berko  -  ENES11D

OO Scale

Kit Double Yellow Signal 3 Aspect Kit

SORRY NO LONGER MANUFACTURED

Eckon/Berko  -  ENES12

OO Scale

Kit Section Signal 4 Aspect Kit 12v DC

SORRY NO LONGER MANUFACTURED

Eckon/Berko  -  ENESWALL

OO Scale

Wall Bracket Only – no signal

Eckon/Berko  -  ENES18 LEFT HAND or RIGHT RAND ASSEMBLY

OO Scale

Kit Junction Signal 3 x 3-Aspect Kit 12v DC

Eckon/Berko  -  ENES19

OO Scale

Kit Junction Signal 2 x 2x2-Aspect 3-Way Kit 12v DC

Eckon/Berko  -  ENES20

OO Scale

Kit Call On Signal Kit 2 Aspect Platform Kit

This is a dual function signal –

The main aspects are for controlling a train leaving its current position on a slow or main line.

A train may be stopped in a platform or on a through line, with a RED and

the single offset ORANGE/YELLOW used to indicate to the driver that he may proceed very slowly with caution into a siding to the Left or Right , that is a DEAD END.

SORRY - NO LONGER AVAILABLE SORRY NO LONGER MANUFACTURED

Eckon/Berko  -  ENES19D OUR SPECIAL

OO Scale

Kit Junction Signal 2 x 2 x 2-Aspect Distant 3-Way Kit 12v DC

Eckon/Berko  -  ENES20

OO Scale

Kit Call On Signal Kit 2 Aspect Platform Kit

This is a dual function signal –

The main aspects are for controlling a train leaving its current position on a slow or main line.

A train may be stopped in a platform or on a through line, with a RED and

the single offset ORANGE/YELLOW used to indicate to the driver that he may proceed very slowly with caution into a siding to the Left or Right , that is a DEAD END.

SORRY - NO LONGER MANUFACTURED SORRY NO LONGER MANUFACTURED

Eckon/Berko  -  ENES23

OO Scale

Kit Call On Signal Kit 4 Aspect Section Kit 12v DC

This is a dual function signal –

The main aspects are for controlling a train leaving its current position on a slow or main line.

A train may be stopped in a platform or on a through line, with a RED and

the single offset ORANGE/YELLOW used to indicate to the driver that he may proceed very slowly with caution into a siding to the Left or Right , that is a DEAD END.

NO LONGER MANUFACTURED SORRY NO LONGER MANUFACTURED

http://www.modeltrainsuk.co.uk/index.asp

Eckon/Berko  -  ENES24

OO Scale

Kit Position Light Ground Kit 12v DC

Eckon/Berko  -  ENES24Y
OO Scale	New 2008
Position Light Ground Yard Signal Kit (2 White, 1 Yellow) Kit 12v DC
This is a typical modern shunt signal, used to allow movements into and out of a siding.  It has three lights with 1 yellow CAUTION and 2 white  indications.  The signal can be seen at ground level or attached to a signal post below a normal stop signal.  When mounted below a stop signal, they do not show an "on" aspect. The ON indication shows a yellow and white light side by side.  The OFF indication shows two white lights at 45 degrees.

	Eckon/Berko  -  ENES2HEAD OO Scale Kit Two Aspect HEAD ONLY Signal Kit 12v DC 2 ASPECT HEAD ONLY C/W 2 LED’s AND 1 RESISTOR – PLEASE SELECT 2 COLOURS

Eckon/Berko  -  ENES2D

OO Scale

Kit Two Aspect Distant Signal Kit 12v DC

Proceed with caution if yellow aspect shows – Ground mounted

Eckon/Berko  -  ENES2H

OO Scale

Kit Two Aspect Home Signal Kit 12v DC

Starter signal to be used from the end of a station platform – Ground mounted

	Eckon/Berko  -  ENES2S   (STOP / CAUTION) SPECIAL OO Scale Kit Two Aspect Home Signal Kit 12v DC Used at busy main line stations for trains entering a no through road platform or into a long platform that receives more than two trains per platform – Ground mounted (Similar to ENB232 Berko)
	Eckon/Berko  -  ENES3HEAD OUR SPECIAL OO Scale Kit Three Aspect HEAD ONLY Signal Kit
	Special item

Eckon/Berko  -  ENES3

OO Scale

Kit Three Aspect Home/Distant Signal Kit 12v DC

STOP or GO or proceed with caution on a Yellow aspect showing. The next signal might be on Red.

Eckon/Berko  -  ENES3D

OO Scale

Kit Three Aspect Distant Signal Kit

GO or proceed with caution on a one Yellow aspect showing. The next signal might be on Red. Two yellow aspects will probably indicate that the next two signals might be at red.

A means of slowing down trains.

	Eckon/Berko  -  ENES4HEAD OUR SPECIAL OO Scale Kit Signal 4 Aspect Double Yellow HEAD Kit ONLY 12v DC

Eckon/Berko  -  ENES4

OO Scale

Kit Signal 4 Aspect Double Signal Yellow Kit 12v DC

Red is STOP. Green is GO. One Yellow is proceed with caution as the next signal along the line might be red when you reach it.

Two yellow’s mean proceed with caution as the next two signals might be at red when you reach them.

Eckon/Berko  -  ENES5 LEFT HAND or RIGHT HAND ON ASSEMBLY BY YOU

OO Scale

Kit Signal 2 x 2-Aspect Junction Home Kit 12v DC

Starter signal to be used from the end of a station platform or other stopping control – Ground mounted.

Proceed ahead on Green on the main line or to the right (or left if left mounted) onto a branch line.

WIRING DIAGRAM BELOW FOR POINT OPERATION

Eckon/Berko  -  ENES5D   LEFT HAND or RIGHT HAND ON ASSEMBLY BY YOU

OO Scale

Kit Signal 2 x 2-Aspect Junction Distant Kit 12v DC

Caution signal to be used usually following a previous Red Aspect – Ground mounted.

Proceed ahead on Green on the main line or to the right (or left if left mounted) onto a branch line. Proceed with caution if Yellow aspect is showing.

Next signal might be at red – Stop.

WIRING DIAGRAM BELOW FOR POINT OPERATION

Eckon/Berko  -  ENES6 LEFT HAND or RIGHT HAND ON ASSEMBLY BY YOU

OO Scale

Kit Junction Signal 3 x 2-Aspect Kit 12v DC

Starter signal to be used from the end of a station platform or other stopping control – Ground mounted.

Red – Stop. Proceed ahead on Yellow caution or on Green on the main line or proceed to the right (or left if left mounted) onto a branch line.

Eckon/Berko  -  ENES7L

OO Scale

Kit Home L/H Route 2 Aspect Signal Kit 12v DC

Starter signal to be used from the end of a station platform or other stop control point– Ground mounted on pole.

Red stop – Green GO. If feather is lit the line might curve to the left sharply or train will have to change tracks to the left.

Might also be used to show the driver what platform he is to enter at a main line station.

Eckon/Berko  -  ENES7R

OO Scale

Kit Home R/H Route 2 Aspect Signal Kit 12v DC

Starter signal to be used from the end of a station platform or other stop control point– Ground mounted on pole.

Red stop – Green GO. If feather is lit the line might curve to the right sharply or train will have to change tracks to the right.

Might also be used to show the driver what platform he is to enter at a main line station.

Eckon/Berko  -  ENES7LS   (STOP / CAUTION)

OO Scale

Kit Home L/H Route 2 Aspect Signal Kit 12v DC

Starter signal to be used from the end of a station platform or other stop control point– Ground mounted on pole.

Red stop – Yellow proceed at low speed. If feather is lit the line might curve to the left sharply or train will have to change tracks to the left.

Might also be used to show the driver what platform he is to enter at a main line station.

	Eckon/Berko  -  ENES7RS (STOP / CAUTION) OO Scale Kit Home R/H Route 2 Aspect Signal Kit 12v DC Starter signal to be used from the end of a station platform or other stop control point– Ground mounted on pole. Red stop – Yellow proceed at low speed. If feather is lit the line might curve to the right sharply or train will have to change tracks to the right. Might also be used to show the driver what platform he is to enter at a main line station.

Eckon/Berko  -  ENES8L

OO Scale

Kit Home/Distant L/H Route 3 Aspect Signal Kit 12v DC

Starter signal to be used from the end of a station platform or other stop control point– Ground mounted on pole.

Red stop – Green GO. If feather is lit the line might curve to the left sharply or train will have to change tracks to the left.

If yellow aspect aspect shows proceed with caution.

Eckon/Berko  -  ENES8R

OO Scale

Kit Home/Distant R/H Route 3 Aspect Signal Kit

Starter signal to be used from the end of a station platform or other stop control point– Ground mounted on pole.

Red stop – Green GO. If feather is lit the line might curve to the right sharply or train will have to change tracks to the right.

If yellow aspect aspect shows proceed with caution.

Eckon/Berko  -  ENES9L

OO Scale

Kit Signal Double Yellow L/H Route 4 Aspect Kit 12v DC

Four aspect signal - Ground mounted on pole.

Red stop – Green GO. If feather is lit the line might curve to the left sharply or train will have to change tracks to the left.

If one yellow aspect shows proceed with caution. If 2 Yellows show the next two signals ahead might be on Red.

Eckon/Berko  -  ENES9R

OO Scale

Kit Signal Double Yellow R/H Route 4 Aspect Kit 12v DC

Four aspect signal - Ground mounted on pole.

Red stop – Green GO. If feather is lit the line might curve to the right sharply or train will have to change tracks to the right.

If one yellow aspect shows proceed with caution. If 2 Yellows show the next two signals ahead might be on Red.

CMENL2G   LED - GREEN with GREEN and WHITE wires

All Scales

Pre Wired LED Green - 1 complete with resistor

CMENL2R  -   LED - RED with RED and WHITE wires

All Scales

Pre Wired LED Red - 1 complete with resistor

CMENL2Y LED - YELLOW with YELLOW and WHITE wires

All Scales

Pre Wired LED Yellow - 1 complete with resistor

CMENL2Y4 - 4^th ASPECT LED - YELLOW with BLUE and BLACK wires

All Scales

Pre Wired LED Yellow - 1 complete with resistor

Gaugemaster 2 Aspect SIGNAL SWITCH GM508 A5C

All Scales

A5C Mini-Toggle for “ Aspect Red/Green Signal On /On

Gaugemaster Point Motor Switch GM510 A5H

All Scales

A5H Mini-Toggle for Point Motors

Gaugemaster 3 Aspect SIGNAL SWITCH GM509 A5D

All Scales

A5D Mini-Toggle for “ Aspect Red/Amber/Green Signal On / Centre Off (But used as ON) / On

NEW 2013 PRICE LIST FOR ECKON BERKO SIGNALS

Colour Light Signals by Berko & ECKON
Part No.	Product Description BERKO READY ASSEMBLED	Price inc VAT
B223	2 light signal yellow/green standard offset square head	13.99
B228	2 light signal red/green standard square head	13.50
B232	2 light signal red/yellow standard square head	13.50
B242	2 light signal red/green standard offset square head	13.99
B251	2 light signal yellow/green standard square head	13.50
B301	2 light signal red/green platform starter square head	13.50
B30L	2 light signal red/green offset platform starter LH square head	13.99
B30R	2 light signal red/green offset platform starter RH square head	13.99
B362	2 light signal red/green short post T junction square head	17.99
B401	2 light signal yellow/green T junction square head	17.99
B462	2 light signal red/green T junction square head	17.99
B503	3 light signal red/green/yellow standard square head	15.00
B533	3 light signal red/green/yellow T junction square head	18.50
B551	3 light signal red/green/yellow standard offset square head	15.00
B604	4 light signal red/green/2yellow standard square head	15.00
B644	4 light signal red/green/2yellow T junction square head	19.80
B664	4 light signal red/green/2yellow standard offset square head	16.99
B801	3 light signal red/green/yellow ground	12.00
	ECKON KITS
EA1	4mm Etched Brass ladder X3	3.00
EA2	2mm Etched Brass ladder X6	3.60
EA3	Route indicator kit LH	7.75
EA4	Route indicator kit RH	7.75
EA7	Speed Restriction sign kit	6.00
EE1	Lectralok lever switch on/off	6.90
EE2	Lectralok lever switch 2-way	7.50
EE3	Lectralok lever switch 3-way	7.50
EET	8BA N/Silver tags for Lectralok switches (20)	2.40
ES1	2 aspect platform starter kit round head	7.75
ES17	4-2 aspect junction kit round head	13.75
ES18	3-3 aspect home junction kit round head	13.75
ES19	2-2-2 aspect home 3 way junction kit round head	14.40
ES24	position light ground signal kit 2white 1red	10.80
ES24Y	position light ground yard signal kit 2white 1yellow	10.80
ES2D	2 aspect distant kit round head	7.75
ES2H	2 aspect home kit round head	7.75
ES3	3 aspect home kit round head	9.18
ES3D	3 aspect distant kit round head	9.18
ES4	4 aspect section kit round head	10.20
ES5	2-2 aspect home junction kit round head	10.80
ES5D	2-2 aspect distant junction kit round head	10.80
ES6	3-2 aspect home junction kit round head	12.55
ES7L	2 aspect home with RT indicator kit LH round head	15.00
ES7R	2 aspect home with RT indicator kit RH round head	15.00
ES8L	3 aspect home with RT indicator kit LH round head	16.20
ES8R	3 aspect home with RT indicator kit RH round head	16.20
ES9L	4 aspect section with RT indicator LH round head	18.00
ES9R	4 aspect section with RT indicator RH round head	18.00
MODELTRAINSUK at CRAVENMODELS OF SHROPSHIRE

N GAUGE ASSEMBLED COLOUR LIGHT SIGNALS

ENBN02	Berko	2 Aspect (Red/Green) Platform Starter	14.70
ENBN03L	Berko	3 Aspect Offset Platform Starter LH	16.35
ENBN03R	Berko	3 Aspect Offset Platform Starter	16.35
ENBN04T	Berko	N 2 Light (Red/Green) Two Head Island Platform Starter	24.95
ENBN0L	Berko	2 Light Red/Green LH Offset Platform Starter	14.90
ENBN0R	Berko	2 Light Red/Green RH Offset Platform Starter	14.90
ENBN28	Berko	2 Aspect (Red/Green) Signal	14.70
ENBN31	Berko	N 3 Aspect Standard Offset Signal	16.00
ENBN32	Berko	3 Aspect Platform Starter	15.90
ENBN36T	Berko	N 3 Aspect Platform Starter	26.40
ENBN38	Berko	Gauge 3 Aspect (Red/Yellow/Green) Colour Light Signal	15.90
ENBN41	Berko	Offset RH Short Arm (Red/Green) Signal	15.90
ENBN62J	Berko	N Twin Head Two Aspect Junction Signal	29.95
ENBN77	Berko	2 Light Red/Green Ground Signal	11.80

102HEAD ONLY	2-Aspect Red/Green c/w Fading Interface Board – HEAD ONLY – NO POST OR LADDER Just Head for Gantry Mounting with long lead wires and PCB
103HEAD ONLY	2-Aspect Yellow/Green c/w Fading Interface Board – HEAD ONLY – NO POST OR LADDER Just Head for Gantry Mounting with long lead wires and PCB
104HEAD ONLY	3-Aspect Red/Yellow/Green c/w Fading Interface Board – HEAD ONLY – NO POST OR LADDER Just Head for Gantry Mounting with long lead wires and PCB
105HEAD ONLY	3-Aspect Yellow/Green/Yellow c/w Fading Interface Board – HEAD ONLY – NO POST OR LADDER
107 HEAD ONLY	4-Aspect Red/Yellow/Green/Yellow c/w Fading Interface Board
181	Steam Era 4 Track Gantry Kit (Signal heads not included) OO Brass – Needs to be assembled by soldering

CANTILEVER SIGNAL GANTRIES – PLASTIC KITS

MODELTRAINSUK - MODEL SIGNAL KITS

www.modelsignals.co.uk

DOUBLE CANTILEVER TRACK SIGNAL PLATFORM OR SINGLE TRACK CANTILEVER SIGNAL

Modeltrainsuk at Cravenmodels 4 Track Signal Gantry Kit No CA2552

Signal power wires and connectors are all hidden from view. Easy installation and maintenance of Signals, wires and connectors.

THIS RANGE OF SIGNAL GANTRY KITS WILL MAKE A VARIETY OF MODELS TO SUIT YOUR LAYOUT – SIGNAL HEADS NOT INCLUDED IN KITS

For a platform model just reduce the height of the central stansion. The cantilever arms can be increased or reduced.

Not included in kit.

To assemble these kits you will need a cutting mat and a sharp modellers knife plus a small hole drill.

Cut out the plastic parts and just cement them together. Plastic cement is NOT included

DAPOL PLASTIC KIT – Several can be joined together to cover many tracks

This plastic Gantry comes with three dummy non working colour light signals. Some modellers drill a small hole in the centre of each dummy aspect and fit small LED’s into the holes. Can be quite effective. Or use ECKON Wall Signal Kits. ENES10 or 11 or 12, or Traintronics Heads – shown above.	Dapol CO 17 OO Scale Signal Gantry

READY ASSEMBLED BURKO GROUND SIGNAL

Eckon/Berko  -  ENB801

OO Scale

GROUND 3 Light Signal 12v DC GREEN YELLOW RED

NEW MAY 2009

OTHER COMPLEMENTARY PRODUCTS – VIESSMANN

BANNER REPEATER SEMAPHORE SIGNALS

An illuminated – Centrally pivoted Semaphore arm in a glass case, showing the indication of the signal

which may be hidden from view when a train stops at a station platform.

E.g. On lines used by express and stopping trains. The express train driver needs to see the signal well

before approaching the station at speed – It could be positioned high in the air if there are surrounding

buildings. The stopping train driver can also see the signal as he approaches the station, but when he

stops at the platform he cannot see his signal which may be many feet in the air above the train – So a

Banner Repeater signal is used so that the driver can see the correct indication of the signal at his eye

level height.

STOP GO

Viessmann  -  VN4515

HO Scale

Marker Signal Banner REPEATER height 55mm - movable banner arm and lit, compact, under baseboard drive unit